Showing 1-10 of 79 results

Browse for Cure Glue best prices at PriceSero.com

  • Bob Smith Industries BSI-157H Maxi Cure/Insta-Set Combo Pack (3 oz. Combined)

    Maxi-Cure extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the ...
    Cure Glue

    • ASIN: B0166FFCHS
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 707336157087

  • Bob Smith Industries BSI-142 Clear Foam-Cure, Craft Glue, 4 oz.

    FOAM-CURE is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE works ...
    Cure Glue

    • ASIN: B011XWDTOW
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 707336142007

  • Bob Smith Industries BSI-135H Maxi-Cure Extra Thick Super Glue, 1 oz.

    Maxi-Cure extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. Directions in 5 different langua...
    Cure Glue

    • ASIN: B0166FFCFU
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 707336135085

  • Insta-Cure Gap Filling 2oz Bob Smith Ind.

    Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
    Cure Glue

    • ASIN: B0000DD1QQ
    • Color: Original Version
    • Brand: Bob Smith Industries
    • UPC: 707336108003

  • Bob Smith Industries BSI-133H Insta-Cure+ Gap Filling Super Glue, 1 oz.

    Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used.
    Cure Glue

    • ASIN: B0166FFCIM
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 707336133081

  • UV Resin - 200g Upgrade Crystal Clear Hard Glue Ultraviolet Curing Epoxy Resin for Jewelry Making Craft Decoration - Transparent Solar Cure Sunlight Activated Thin Resin for Mold, Casting and Coating

    UV Craft Resin makes fun stuff fun to make! Let your imagination be your guide for casting, coating and other DIY crafts. The possibilities are endless! Combine with our mica powder or liquid colorants to create custom colored glass or solid color appearance. Great for art and craft projects for all ages and abilities. Click 'Add to Cart' with no hesitation now!
    Cure Glue

    • ASIN: B07JL7YFYR
    • Brand: DecorRom
    • UPC: 646690136751

  • Bob Smith Industries BSI-161H UN-CURE Super Glue Debonder, 1 oz.

    UN-CURE deboned will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Directions in 5 different languages.
    Cure Glue

    • ASIN: B0166FFC96
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 707336161084

  • 3 Pack IC-Gel Insta Cure Cyanoacrylate Gel Coral Glue .7oz / 20 g

    IC-GELTM is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURETM. IC-GELTM, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GELTM can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second afte...
    Cure Glue

    • ASIN: B01N026YZU
    • Brand: Bob Smith Ind Glue
    • UPC: 707336116008

  • Bob Smith Industries BSI-131H Insta-Cure Thin Super Glue, 1 oz.

    Super thin glue that penetrates into joints.
    Cure Glue

    • ASIN: B01FUFWN8Q
    • Color: Clear
    • Brand: Bob Smith Industries
    • UPC: 007336131088

  • Bob Smith Industries BSI-109 Insta-Cure Gap Filling, 8 oz.

    Insta-cure+ is a higher viscosity ca for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker ca is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, insta-cure+ should also be used. To prevent premature curing, do not spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread out.
    Cure Glue

    • ASIN: B01140EHFI
    • Brand: Bob Smith Industries
    • UPC: 707336109000

  • Surehold SH22051 4 g Light Cure Super Glue with Light

    Light Cure Super Glue-4g W/Light
    Cure Glue
    Bond and repair things in seconds! Good for plastic, wood, fabric, leather, metal, and more. This 3.75x6.5 inch inch package contains one .14 oz of light cure super glue and one LED light with battery. Multi-material, dual curing, non-irritating, high photo sensitivity, non-staining, and odorless.WarningChoking HazardNot suitable for children under 3 yearsKeep away from childrenFor adult use onlySpecificationsCapacity: 4 gDimension: 0.5" H x 3.8" W x 6.5" D- SKU:

    • UPC: 622892892
    • Model: SH22051
    • Color: Multicolor

  • Insta-Cure Plus Gap Filling CA Glue 4oz Bob Smith Industries

    BSI134 Insta-Cure Plus Gap Filling CA Glue 4oz Bob Smith Industries A thick, flow resistant super glue. INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, do not spread the glue into a thin film. Lay down a serpentine bead with about 1in. Separations on one surface,
    Cure Glue
    Insta-Cure Plus Gap Filling CA Glue 4oz Bob Smith Industries

    • UPC: 499370344
    • Model: MODB00E4VZ326

  • Bob Smith Ind CA Glue Insta-cure Super Thin -1/2 ounce

    Bob Smith Ind CA Glue Insta-cure Super Thin
    Cure Glue
    Insta-Cure Super Thin CA Adhesive Glue INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface

    • UPC: 135182655
    • Model: MODB014RYHIQS
    • Color: White
    • Size: 2 fl oz1/2 ounce

  • Bob Smith Ind CA Glue Maxi-Cure Extra Thick -3/4 ounce

    Bob Smith Ind CA Glue Maxi-Cure Extra Thick
    Cure Glue
    Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other

    • UPC: 133948277
    • Model: BSI135
    • Size: 4 fl oz3/4 ounce

  • Bob Smith CA Glue Insta-cure + Gap Filling - 8 ounce

    Bob Smith CA Glue Insta-cure + Gap Filling
    Cure Glue
    INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, do not spread the glue into a thin film. Lay down a serpentine bead with about 1in. separations on one surface, then assemble the parts, letting the pressure spread the CA

    • UPC: 185876253
    • Model: BSI109
    • Size: 8 oz8 fl oz

  • How To Fast Cure Gorilla Glue

    Cure Glue
    This video shows you how to fast cure Gorilla Glue using common household items. You can control how much the glue expands or not, how to make it into a paste etc. Typical cure time is 30 to 45 m...
    gorilla,glue,gorilla glue,fast,cure,fast cure,speed up,faster,rapid,polyurethane,how,how to,how t...

    What is E6000 industrial adhesive glue used for? - pros, cons, uses, instructions, drying times

    Cure Glue
    What is #E6000 industrial adhesive #glue used for? - pros, cons, uses, instructions, drying times and more - a comprehensive review Amazon Affiliate link: https://amzn.to/2IR841I How to use it o...
    Maker,E6000,e6000 adhesive,e6000 glue on wood,e6000 crafts,e6000 diy,e6000 dry time,e6000 dry fas...

    Super Glue Corner With Bill

    Cure Glue
    Bill discusses cyanoacrylate super glue and how awesome it is for EVA foam! Insta-cure http://amzn.to/1K4nEFb Insta-set http://amzn.to/1AYj4km Un-cure http://amzn.to/1vONHtu Punished Props Miss...
    Glue,super,bond,spray,foam,cure,cyanoacrylate,punished,props